Speed limiter with control for electric scooter or electric vehicle (3.7 to 12v)
€64.00
Speed limiter with control for electric scooter or electric vehicle (3.7 to 12v)
Limit engine power with this remote control speed controller.
This device limits the speed of your engine using a remote control that you can carry in your pocket or on your key ring.
**
Technical specifications:
-Speed limiter with 433MHZ frequency
-Prepared for supply voltages of (3.7 to 12v), it can be connected to the 5v supply of the hall sensors or 3.3v of the bluetooth module, voltages available in most controllers so it does not need a voltage regulator for your installation.
-Maximum charge current: 1A (700mA maximum current is recommended in continuous work)
- Quiescent current: 4ma
-Size of the board without box: 34 x 14 x 7.4mm
- Case size: 39.5 x 20 x 10.5mm
Connection ways available:
-Port normally open (NO)
-Common Port (COM)
-Port normally closed (NC)
Operating modes: Push button, switch and signal with delay. Detailed configuration below.
Electric scheme:
Red = Positive.
Black = Negative.
White = Normally open.
Yellow = Common.
Blue = Normally closed.
**
Security policy.
Secure purchase with SSL security certificate. Secure payment methods: Paypal or 3D Secure.
delivery policy
Specific and precise delivery times. More than 48,000 packages delivered.
Warranty
Product guarantee, you will receive what you bought. Free installation help and support
The relay with the command can be configured in the following modes:
Pushbutton mode: The relay remains active when the command is pressed, inactive when it is released.
Press the learn button 1 time. Then press the button on the remote, the indicator. If the led on the board flashes 1 time and goes off, it has been configured correctly.
Switch mode: The relay is activated when the button is pressed once and deactivated when it is pressed again.
Press the learn button 2 times. Then press the button on the remote, the led indicator flashes 2 times and goes off, which means successful learning.
Delayed disconnection/connection mode:
-Off-delay time (5s): Press the learning button 3 times. Then press the transmitter button A, the Led indicator flashes 3 times, then press the transmitter button B, the Led indicator turns off, which means learning successful.
-Off-delay time (10S): Press the learning button 4 times. Then press the transmitter button, the Led indicator flashes 4 times and goes off, which means successful learning.
-Off-delay time (15S): press the learning button 5 times. Then press the button on the transmitter, the Led indicator flashes 5 times and goes off, which means successful learning.
-Off-delay time (20S): Press the learning button 6 times. Then press the transmitter button, the Led indicator flashes 6 times and goes off, which means successful learning.
Reset: Press the learning button 8 times until the Led indicator of the receiver flashes 8 times, which means the setting has been cleared (before changing the working mode you must clear the code first)
Speed limiter with remote for electric scooter or electric vehicle (3.7 to 12v) - We are specialists in parts, improvements, replacement parts for any electric scooter, electric bicycle or electric vehicle. Tires, brakes, engines, fairing, accessories, damping systems, etc... If you can't find what you are looking for, contact us: whatsapp +34 696403761
4 Items
Comments (0)
Speed limiter with control for electric scooter or electric vehicle (3.7 to 12v)
Limit engine power with this remote control speed controller.
This device limits the speed of your engine using a remote control that you can carry in your pocket or on your key ring.
**
Technical specifications:
-Speed limiter with 433MHZ frequency
-Prepared for supply voltages of (3.7 to 12v), it can be connected to the 5v supply of the hall sensors or 3.3v of the bluetooth module, voltages available in most controllers so it does not need a voltage regulator for your installation.
-Maximum charge current: 1A (700mA maximum current is recommended in continuous work)
- Quiescent current: 4ma
-Size of the board without box: 34 x 14 x 7.4mm
- Case size: 39.5 x 20 x 10.5mm
Connection ways available:
-Port normally open (NO)
-Common Port (COM)
-Port normally closed (NC)
Operating modes: Push button, switch and signal with delay. Detailed configuration below.
Electric scheme:
Red = Positive.
Black = Negative.
White = Normally open.
Yellow = Common.
Blue = Normally closed.
**